Welcome: Orson Pump Co., Ltd.

info@orsonpump.com 0086-0311-85456888

Mission Centrifugal Pump

Size: 1" to 22"
Capacity: 3.6-5400 m3/h
Head: 6-125 m
Handing solids: 0-130mm
Concentration: 0%-70%
Materials: Hyper chrome alloy, Rubber, Polyurethane, Ceramic, Stainless steel etc.

     Description     


Orson® Pump AH Series Slurry Pump is a kind of the Horizontal centrifugal slurry pump. They are widely used in mining, coal, metallurgy, electric power and other industrial sectors to transport slag with strong corrosion and high concentration. This series of pumps can be applied to various working conditions with high performance and low maintenance cost. 


The flow rate range of slag slurry with

▲ High concentration and high corrosion property is 40-80%.

▲ Medium concentration and medium corrosion property is 40-100%.

▲ Low concentration and low corrosion property is 40-120%.


    Cost Savings    

● Cost life effective.

● Replacement parts are dimensionally interchangeable with the Warman AH, L, HH, G, SP series pumps.

● Reduced stock holidng due to extended service life.

● Highly resistant to swelling from chemical attack.

● Orson® pump has increased slurry pump wet end life up to four and half times.

● The cost of rubber or steel parts to run 3375 hours was $9600. the mine has saved $18125 on just one pump in 4.5 months.


2.jpg

    Performance Parameters    

image.png


    Outline Dimensions    


20181227162119_360.jpg


image.png

    Structure and Characteristics    

图片11.jpg

图片10.jpg

▲ The large diameter and Short cantilever ensure the rigidity of the shaft, which is suitable for high power and harsh working conditions.

▲ The hardened stainless steel shaft sleeve has O-rings at both ends to protect the shaft from abrasion and corrosion.

▲ The front and rear cover plates of the impeller have secondary blades, which can reduce backflow and seal pressure.

▲ The pump body and the pump cover are made of ductile iron with reinforcing ribs, which ensures the ability to withstand high pressure.

▲ The flow parts are made of a variety of high chromium anti-wear alloys, which have the characteristics of wear resistance, corrosion resistance, impact  resistance and so on, greatly improving the service life of the pump.

▲ Different impellers can be selected according to different working conditions.

▲ The outlet position of the pump can be installed and used by rotating eight different angles as required.

▲ There are two different lubrication methods for bearing components, and appropriate lubrication methods should be selected according to different working conditions.

    Sealing Form    

▲ Packing seal: The most widely used sealing form, through the front water seal ring continuously inject a certain pressure of clear water into the packing, to prevent the slurry leakage in the pump, for not suitable for sealing with the secondary impeller, stuffing seal is usually used. The packing sealing structure is simple and the maintenance is convenient.

▲ Mechanical Seal: Used when sealing requirements are relatively high. Especially in some chemical and video fields, not only sealing is required, but also additional components are not allowed to enter the pump chamber.

▲ Secondary impeller seal: Through the impeller acting force of a reverse centrifugal force, prevent the slurry from leaking out. The secondary impeller seal has the advantages of no need of shaft seal water, no dilution of slurry and good sealing effect. Therefore, this sealing form can be considered under the condition that dilution of slurry is not allowed.

INQUIRY

CATEGORIES

CONTACT US

Contact: Eric

Phone: 0086-15369359399

E-mail: info@orsonpump.com

Whatsapp:0086-15369359399

Add: No. 028, Tianshan St, High-tech Zone, Shijiazhuang City 050000, China.