Welcome: Orson Pump Co., Ltd.

info@orsonpump.com 0086-0311-85456888

Orson® M Medium Slurry Pump

Size: 8" to 10"
Capacity: 600-1820 m3/h
Head: 15-75 m
Handing solids: 0-85mm
Concentration: 0%-70%
Materials: Hyper chrome alloy, Rubber, Polyurethane, Ceramic, Stainless steel etc.


Orson® M Medium Slurry Pump is a kind of the Horizontal centrifugal slurry pump. The medium pump for slurry are widely used in mining, coal, metallurgy, electric power and other industrial sectors to transport slag with strong corrosion and high concentration. The pump for slurries can be applied to various working conditions with high performance and low maintenance cost. 

The flow rate range of slag slurry with

▲ High concentration and high corrosion property is 40-80%.

▲ Medium concentration and medium corrosion property is 40-100%.

▲ Low concentration and low corrosion property is 40-120%.

Cost Savings.jpg

● Cost life effective.

● Replacement parts are dimensionally interchangeable with the Warman AH, L, HH, G, SP series.

● Reduced stock holidng due to extended service life.

● Highly resistant to swelling from chemical attack.

● Orson® pump has increased slurry pump wet parts end life up to four and half times.

● The cost of rubber or steel parts to run 3375 hours was $9600. the mine has saved $18125 on just one pump in 4.5 months.

the pump for slurry

Performance Parameters.jpg

the pump for slurries performance parameters

Outline Dimensions.jpg

the outline dimension of Orson® M Medium Slurry Pump

outline size of Medium Slurry Pump

Structure and Characteristics.jpg

Structure of pump for slurry

Characteristics of pump for slurry

▲ The large diameter and Short cantilever ensure the rigidity of the shaft, which is suitable for high power and harsh working conditions.

▲ The hardened stainless steel shaft sleeve has O-rings at both ends to protect the shaft from abrasion and corrosion.

▲ The front and rear cover plates of the impeller have secondary blades, which can reduce backflow and seal pressure.

▲ The pump for slurry body and cover are made of ductile iron with reinforcing ribs, which ensures the ability to withstand high pressure.

▲ The flow parts are made of a variety of high chromium anti-wear alloys, which have the characteristics of wear resistance, corrosion resistance, impact  resistance and so on, greatly improving the service life of the pump.

▲ Different impellers can be selected according to different working conditions.

▲ The outlet position of the pump for slurry can be installed and used by rotating eight different angles as required.

▲ There are two different lubrication methods for bearing components, and appropriate lubrication methods should be selected according to different working conditions.

Sealing Form.jpg

▲ Packing seal: The most widely used sealing form, through the front water seal ring continuously inject a certain pressure of clear water into the packing, to prevent the slurry leakage in the pump, for not suitable for sealing with the secondary impeller, stuffing seal is usually used. The packing sealing structure is simple and the maintenance is convenient.

▲ Mechanical Seal: Used when sealing requirements are relatively high. Especially in some chemical and video fields, not only sealing is required, but also additional components are not allowed to enter the pump chamber.

▲ Secondary impeller seal: Through the impeller acting force of a reverse centrifugal force, prevent the slurry from leaking out. The secondary impeller seal has the advantages of no need of shaft seal water, no dilution of slurry and good sealing effect. Therefore, this sealing form can be considered under the condition that dilution of slurry is not allowed.




Contact: Eric

Phone: 0086-15369359399

E-mail: info@orsonpump.com


Add: No. 028, Tianshan St, High-tech Zone, Shijiazhuang City 050000, China.