Welcome: Orson Pump Co., Ltd.

info@orsonpump.com 0086-0311-85456888

Orson® L Light Slurry Pump

Pump caliber: 20mm-650mm
Capacity: 500-10260 m3/h
Head: 5-63 m
Handing solids: 0-130mm
Concentration: 0%-70%
Materials: Hyper chrome alloy, Rubber, Polyurethane, Ceramic, Stainless steel etc.

Description.jpg


Orson® Light Slurry Pump is also called Small slurry pump. This name is not only for its size, but also for its price. Compared with heavy duty slurry pump, this kind of pump has high rotating speed, small volume and light weight, and is suitable for coverying fine particles and low concentration slurry.

The flow rate range of slag slurry with

▲ High concentration and high corrosion property is 45-85%.

▲ Medium concentration and medium corrosion property is 45-100%.

▲ Low concentration and low corrosion property is 50-120%.


Cost Savings.jpg

● Cost life effective.

● Replacement parts are dimensionally interchangeable with the Warman AH, L, HH, G, SP series.

● Reduced stock holidng due to extended service life.

● Highly resistant to swelling from chemical attack.

● Orson® small slurry pump has increased slurry pump wet parts end life up to four and half times.

● The cost of rubber or steel parts to run 3375 hours was $9600. the mine has saved $18125 on just one pump in 4.5 months.


2.jpg

Performance Parameters.jpg

image.png


    Outline Dimensions    


outline dimensions of small slurry pump


image.png


Structure and Characteristics.jpg

Structure of small slurry pump

Characteristics of small slurry pump

▲ The large diameter and Short cantilever ensure the rigidity of the shaft, which is suitable for high power and harsh working conditions.

▲ The hardened stainless steel shaft sleeve has O-rings at both ends to protect the shaft from abrasion and corrosion.

▲ The front and rear cover plates of the impeller have secondary blades, which can reduce backflow and seal pressure.

▲ The small slurry pump body and cover are made of ductile iron with reinforcing ribs, which ensures the ability to withstand high pressure.

▲ The flow parts are made of a variety of high chromium anti-wear alloys, which have the characteristics of wear resistance, corrosion resistance, impact  resistance and so on, greatly improving the service life of small slurry pump.

▲ Different impellers can be selected according to different working conditions.

▲ The outlet position of the pump can be installed and used by rotating eight different angles as required.

▲ There are two different lubrication methods for bearing components, and appropriate lubrication methods should be selected according to different working conditions.

Sealing Form.jpg

▲ Packing seal: The most widely used sealing form, through the front water seal ring continuously inject a certain pressure of clear water into the packing, to prevent the slurry leakage in the small pump, for not suitable for sealing with the secondary impeller, stuffing seal is usually used. The packing sealing structure is simple and the maintenance is convenient.

▲ Mechanical Seal: Used when sealing requirements are relatively high. Especially in some chemical and video fields, not only sealing is required, but also additional components are not allowed to enter the pump chamber.

▲ Secondary impeller seal: Through the impeller acting force of a reverse centrifugal force, prevent the slurry from leaking out. The secondary impeller seal has the advantages of no need of shaft seal water, no dilution of slurry and good sealing effect. Therefore, this sealing form can be considered under the condition that dilution of slurry is not allowed.

INQUIRY

CATEGORIES

CONTACT US

Contact: Eric

Phone: 0086-15369359399

E-mail: info@orsonpump.com

Whatsapp:0086-15369359399

Add: No. 028, Tianshan St, High-tech Zone, Shijiazhuang City 050000, China.